The Swiffer Wet Jet cleaner runs on battery. The machine has nozzles that spray off cleaning solution from a tank. The machine also has cleaning pads and motors to carry out its primary function: cleaning. So if your Swiffer Wet Jet isn’t spraying properly, you reckon something has gone wrong within these components.
The batteries could be dead, or the nozzle or motor could become dirty. It is also possible that the assembling has gone wrong somewhere. And fixing each problem is relatively simple too. Changing batteries, unclogging and cleaning, and re-installing Swiffer Jet components aren’t too rigorous.
Now that we established the possible reasons for your jet to go bust, let’s dive in deeper. Stay along as we detail the problems and provide solutions to each of them.
You may like: Why O Cedar Spray Mop Leaking Water
Causes and Solutions on Why Is My Swiffer Wetjet Not Spraying Properly
Dead Batteries
The simplest reason why your machine would stop spraying has to be dead batteries. After long-term use, you will have to replace the batteries. Switch off your mop and remove the cleaning solution bottle.
Then locate the battery compartment near the junction where the handle is attached. Remove the old batteries and switch with the new ones. Keep in mind you will need AA batteries.
Close the compartment and re-install the cleaning solution bottle. Start the jet. If you still don’t see any improvement, try out the other solutions we have detailed.
Clogged Nozzles
If you hear the motor humming but no spray coming out of the nozzles, then there must be some clogs.
To get rid of the clogs, shoot a fine stream of water through the nozzles. Use a hosepipe to clean the insides for around 30 seconds.
Or you can also use a toothpick, needle, or similar pointy objects to poke around and clean any clogs. If that still doesn’t help, keep reading.
Problems With The Tank
Before you start cleaning, make sure the tank is completely filled. The tank can hold up to 500 ml of cleaning fluid. It is possible that there isn’t a sufficient amount of cleaning solution inside the tank.
Refill the container and again try spraying. If that doesn’t work, then it is also possible that the tank is incorrectly fitted. Improper installation can be the reason why the spray isn’t being properly ejected, or ejected at all.
Simply detach the container and re-adjust it. See if that helps. If not, don’t be wary. Keep reading and see if the remaining troubleshooting would help.
Unclean Filters
The filters can become dirty and clog up the system. To clean the filters, remove the water tank and locate the filter cover.
Remove the filters and clean them under running water. Air dry after washing and place them back into the filter cover. Put the water tank back into its place and see if that helps fix the problem.
Improper Padding Installation
The pads at the bottom may not have been properly put in place. And that can hinder the nozzles from properly jetting a spray.
Remove the pad and place a new pad in its place. Attach the printed side with the brand name to the Swiffer Wet Jet.
Problems With The Motor
The most obvious signs of motor damage would be when you turn on the mop but the motor doesn’t make any humming sound. To fix the motor, you would have to dismantle the jet.
First, remove the batteries and the cleaning solution before opening. To open, remove the screws from the inside where the bottle sits, from each side of the circle. Then unscrew the larger screw on the outside.
Separate the two halves. You would have to press the smaller half as both sides are held together by tabs that have to be unhinged. After that, locate the motor. Use a screwdriver to manually turn it.
Check for any rust that has developed on the motor. Clean off any accumulated dirt too. Apply dry lubricant to the motor and rusted terminals. After that, see if the motor is functioning properly by turning on the spray button.
The motor should once again make the humming sound if there aren’t any clogs or problems with it.
Final Words
So there you have it! We have listed out some of the most common reasons that can cause your Swiffer jet to not spray properly. It can at first seem a bit tedious to fix your Swiffer Wet Jet. But be assured, most of the reasons here do not involve much intervention, except for the motor.
To summarize, these are the common reasons your Swiffer may not spray properly: dead batteries, clogged nozzles, unclean filters, lack of cleaning solution, improper installation, and damaged motors.
We hope that this article has helped you to troubleshoot your question to ‘why is my Swiffer WetJet not spraying properly’ and go back to your cleaning.